Installing artificial grass putting greens

The goal is to create a smooth and uniform base; the green will not hide irregularities in the base. A properly compacted base will not show a footprint when walked on. Once the base preparation is complete, avoid any unnecessary surface traffic. Installing your Cup s : How to Install Concrete Cups for Putting Greens Arrange the artificial putting green cups on the crushed granite as you would like them. Mark where your cups will be permanently placed. This can be done by applying pressure to each cup and rotating it.

This will cause a small indentation in the crushed granite which will be used as a reference point. With a small hand shovel dig a small hole that is 2 inches larger in diameter than the cup itself and equal in depth. Use fast-drying concrete mix powder around the entire outside perimeter. Pack down the mix. Finishing your Base: Small ridges caused from the plate compactor on your base need to be removed.

The putting green surface needs to fit like a glove to your base so you want it as smooth as possible. Use the bottom of your shovel or hand tool to flatten the ridges. Use a spreader to distribute sand over the entire green.

A 50 lb bag of sand will cover approximately Sq Ft. Use a broom to lightly sweep the sand and any loose gravel off your base. Installing the Artificial Grass for your Putting Green: The install can begin after the grass has been allowed to lay in direct sunlight for two hours. This will allow wrinkles in the backing to settle out.

Use a power broom to brush the grass fibers against the direction they are laying before installation. This will make the installation of infill easier. If seaming sections of grass together, do not brush the fibers until you have removed the edges. If the width of your artificial putting green is less than your roll width you can skip the following steps. Make sure the grain of each roll of artificial putting green is running in the same direction. Place the synthetic putting green turf over the edge of the crushed granite and roll it out.

Make sure there are no significant creases in the turf. If there are tiny creases the weight of the infill will make them go away.

Use a push broom against the grain of the putting green to separate the fibers before putting in the infill. Lay one roll over where the seam will come together. Make sure the backing is face up. With a knife cut between the first and second row of stitching. Do this for only one of the rolls where your seam will be joined. Cutting between the rows will remove the black strip. It will also give you a tight fit and perfect seam.

Use solid base underneath the roll that is being overlapped. This will make for a solid smooth cutting surface. Place bags of infill every 4 ft on both sides along the length of the seam. This prevents movement during the seaming process. Cut the top overlapped roll of turf by following the edge of the bottom roll with a utility knife. Do this with the full length of the seam. Once the seam has been cut, join the 2 pieces together to ensure a tight fit before seaming the rolls together. Continue to replace your utility knife blade after cutting ft.

Nail down the seaming strips on the sub base where the seam will come together. There should be an equal amount of seaming strip on each side of the seam. Apply adhesive over the entire surface of the seaming strip. Allow min for the adhesive to set up and get sticky before seaming. Pull the artificial putting green turf over at the seam. Lay one roll onto the adhesive and seaming tape the full length of the seam.

Carefully join the 2 rolls together. Press the seam in place to get good contact of the turf backing and adhesive. After the entire seam has been placed together walk over the artificial putting green several times. Allow 2 hours before moving on to the next step.

If you desire a fringe around your putting green, use a yardstick to assist with the measurement. Using a string, mark your shape in 1 foot increments. Use a utility knife to cut along the outside perimeter.

Run the fringe turf the length of the putting green on each side first, then the two widths. The grain of the fringe turf must run the same direction all around the green. Roll the fringe turf over one side the length of the putting green. Overlap the entire fringe turf just enough to cover the shape of your artificial putting surface on one side the length of your putting green.

Hammer the nails every 6 inches the entire length of your fringe turf. Not only will it save you money on costly green fees at your local country club, but nothing beats the convenience of being able to enjoy the sport you love from the comfort of your own yard. When it comes to making such a charming addition to your backyard, you have lots of options as to what materials to use for your putting green. Using artificial turf instead of real grass will provide consistent beauty all year long with minimal upkeep, but most importantly, it will provide a high-quality putting space for you to improve your game.

There are several reasons for using artificial turf instead of real grass:. Artificial turf will not incur damage from pets and yard pests like real grass would. Nothing ruins a golf game like brown spots and holes from a dog digging on the putting green. You can place your artificial turf green anywhere. Real grass needs plenty of light, good soil, and moisture, meaning you are limited in where a putting green can be placed in a yard. Artificial turf has the flexibility to be placed in a sunny spot, or under your favorite shade trees.

Artificial turf is low maintenance with no mowing, weeding, or fertilizing required. When you make the wise decision to utilize artificial turf for your putting green, Veridian Putting Green grass is an excellent choice for its durability, optimal surface, and beautiful appearance.

The grass blade fibers are made out of polypropylene, making them more dense and sturdier than other types of artificial grass and certainly sturdier than real grass. Veridian can also be installed over concrete, providing added opportunities for installation. The backing is tough enough to drain liquids and moisture, but flexible enough to be installed on undulated or uneven surfaces to enhance the challenge of putting in your backyard.

If you opt to make installing this a DIY opportunity, there are several options for building your own putting green that is easy and ensures longevity for the turf. For the most part, it can be painless process when keeping these considerations in mind:.

You can make your putting green useful not only for golfing purposes but also landscaping. Many people swoon at the sight of a well-kept golf course, and your backyard can be just as easy on the eyes:. There are almost limitless possibilities when incorporating your putting green into existing landscaping. One of the most important considerations, though, is adding landscaping features that will further your own enjoyment of your putting green.

A major benefit of installing artificial turf for your putting green is that care and maintenance is significantly easier, cheaper, and healthier. You obviously do not have to water your artificial turf multiple times a day, or even weekly. You can, however, rinse it with cool water to remove any dust that may gather.

No fertilizer, lawn mower, or weed-eating is necessary, either. In caring for your artificial turf green, simply take care to remove any stray leaves or branches that land on it as a result of the wind to keep these materials from becoming ground into the turf. This will not only make installation quick and easy, but it will further your enjoyment by completely cutting out the mowing, weeding, and fertilizing required of real grass.

Indeed, using artificial turf on your putting green will enable you to participate in a relaxing pastime in your own backyard, while also contributing to a beautiful overall landscape.